How To Connect Sq11 To Wifi

SQ11 WIFI Transmission. iPhone.

Charging.

Please use a 500-1000 mA charger to charge the equipment. When charging, the red indicator light is always on. When information technology is total, the red indicator light is off. Can piece of work while charging.

Turn on the device.

Press the ability button to first the auto. After starting the auto, the blueish indicator calorie-free flashes continuously and speedily, and the device enters the state to be continued.

Annotation: If the bluish indicator is slow flashing/ever on or cannot be connected, long press the reset push for 5 seconds to reset.

Apple tree IOS operations are equally follows:

one. Install the application.

Download and install JXLCAM. IOS searches for "JXLCAM" download directly at the Apple App Store. For convenience, delight scan the download and installation of the QR code below.

Note: during installation, all permissions of the JXLCAM АРР need to be immune, otherwise the АРР volition not work properly.

Please select АPP to download.

iPhone selection

ii. Local mode

Open the list of mobile phones WIFl, connect to B/xCCQ .., open the APP page after success, click "АР" as shown in the figure below, and picket the video.

Notation: when at that place is no WIFI in the environment, you tin can use АР manner to connect, which is valid for no more than than 10m, which can achieve localized video viewing.

three. Remote mode.

i. First ostend that in that location is а available WIFI near the device, turn on the device, flash the blue indicator light quickly, and the device is in а state to exist continued. ( Annotation: WIFI signals supported only in the 2.4G band)

2. Y'all can't successfully distribute the network when the power is insufficient.

iii. When wiring, delight endeavour to bring the device close to the router. When the nearby WIFI signal is weak, the prototype will be stuck if the network is not successful or the network is successful.

iv. Open the APP and follow these steps;

i) Click "+"

2) Click "AP add Device"

3) Click "..."

4) Click "Settings"

5) Click "WLAN"

half-dozen) Select to connect your 2,4G ring WIFI, and and so click JXLCAM in the upper left corner to render to the АРР.

7) Enter the correct WIFI countersign and click "Next"

8) Click "..."

9) Click "Settings"

10) Click "WLAN"

11) Connect to the device hotspot "B/XCCQ...". Then click JXLCAM in the upper left corner to return to АPP.

12) Click "Add Device"

13) Wait for distribution network

14) After seeing the success of the distribution network, click "Side by side".

15) Customizable name, click "Next".

xvi) You lot can view the camera preview folio on the habitation folio.

four. Home folio icons and button instructions.

- Local mode

- Add device

Camera BCCQ518... - Device nickname

Online - Network status

- SD bill of fare playback file

- Manually tape files

5. Description of icons and buttons on the video folio.

- Settings

- Talk (Products with speakers can exist used)

- Mind

- Photograph

- Recording

- Landscape switching

- Warning

- Switch left and right

- Switch upward and down

- Indicator light ON/OFF

- Infrared lamp ON/OFF

- Sharpness switch

6. Storage card

If you need to store video content, you demand to install an SD card.
(This machine supports loop video recording)

seven. Photographic camera settings

Name - Change the device name

User Config - Modify user name

Move Alert Config - Motion detection sensitivity

Note: sensitivity and alarm interval can be set for move detection. Click "".

Share - Share the QR code to the person who needs to connect the device.

TF - Format TF card

- Restart the device

- Factory information reset

Notation:
1. When the device fails to configure the network, please check whether the router and WiFi countersign are configured correctly (the device does non support WIFI signals in the 5.8G ring). Later on confirming that information technology is correct, yous can press and hold the reset push until the device indicator flashes apace, restore the manufactory settings, and reconfigure network.

2. When the software homepage shows that the device is offline, you can check whether the device is normally powered on, and click the refresh icon in the upper right corner to refresh.

3. The initial password of the device is admin.

FAQ

Why is there no sound or racket when watching the existent-time feed of the camera?
Sound is disabled past default for real-time feeds in the app. The sound tin be enabled by using the volume push button in the live window of the app. If volume is also low, increase the book of your device. If there is whatever noise in the real-time feed, please proceed your phone away from the photographic camera and avoid placing the camera near electronic devices such as refrigerators or microwave ovens.

What should I do if the video freezes or the audio and video are non synchronous when watching the real-fourth dimension feed of the camera?
If the video is dull or frequently loading, please set the video resolution to Hard disk. If the sound and video are not synchronous, please check whether the network the camera is connected to is functioning usually. If in that location is a lot of delay, attempt to exit and reopen the feed.

What should I do if the camera does non broadcast any audio during calls?
Information technology is possible the app does non accept the permissions to access the microphone of your phone. Delight grant the relevant permissions in the settings of your telephone.

What should I exercise if there is an echo during calls?
If in that location is an echo or a whistling sound, try to keep a altitude of 10 meters or more than between your telephone and the camera during the phone call.

How does the memory card store videos?
If a memory card is installed, recorded videos are always stored on the memory bill of fare past default. One time the card is full, the oldest video will exist deleted automatically and the camera will record continuously.

Do I demand to reconnect to the app afterwards changing to a different Wi-Fi network?
Yes. Remove the device from the app, and then press and hold the reset push on the camera for 5 seconds, and add the device again.

What should I practise if I forgot the password for the photographic camera's security settings?
Printing and hold the reset button on the photographic camera for 5 seconds. After the camera is reset successfully, add it to the Mi Dwelling house app again.

How exercise I connect multiple phones to the photographic camera?
In the device settings of the camera monitoring page, you lot tin view the device ID and countersign. The shared user needs to download the APP and manually add the device.

Where is the camera suitable for employ?
Please place the camera indoors, do not place it in an surroundings that is excessively boiling or may cause h2o to enter the product, so as not to affect normal use.

● SQ11 WIFI Manual. Android. ►

● SQ11 mini DV. Transmission. ►

Source: https://org-info.mobi/manual/sq11-wifi-mini-dv-ios.html

Share this post